Z-Bends and Figure-4 clevis fittings. These are used to link MicroAct and MiniAct actuators to control surfaces. These fittings are held onto your control rod by using the included heat shrink tubing. More info »
Set of parts to make your own Bahoma connectors More info »
These are the smallest, yet still usable connectors we could come up with. The same connector we install on our 6mm gearboxes and MiniAct's. Perfect for updating your actuators to this new, smaller standard. Precision machined parts, so they are not cheap. Made in USA. 0.05"(1.27mm) pitch. Female Sockets weigh 0.070g Male Pins Weigh 0.048g. Includes: 5 Male and 5 Female Connectors More info »
These plywood control horns can be used with MiniAct and MicroAct magnetic actuators. Strong and lightweight. Horns weigh 0.036g each. These save you time, just cut a slot in the foam and stick the tab in with a little CA. Can be colored with felt tip marker if desired. 23 Control Horns fit MiniAct and MicroAct More info »
These fiberglass control horns can be used with MiniAct and MicroAct magnetic actuators. PCB substrate - strong and lightweight. Small size (8mm) horns weigh 0.025g each. Medium Size (11mm) horns weigh 0.036g each. These save you time. Can be colored with felt tip marker if desired. More info »
These fiberglass wheels are suitable for sub ounce model aircraft. Made from PCB substrate - strong and lightweight. The 20mm wheels weigh 0.14g each and the 15mm wheels weigh 0.078g each. Decorate with a felt marker. 2 fiberboard Wheels, and two hubs/retainers. More info »
Blenderm Hinge Tape, 12.5mm x 4.57m (0.5 inch by 15 feet) More info »
Mylar - clear .00025 30cm x 78cm. This Mylar is thicker then the mylar used on the Carbon Butterfly. But it's a little easiler to work with. It's rolled onto kraft paper for safe storage and shipping. Used for making repairs to Carbon Butterfly airframe - lightweight covering material. More info »
Connector set - 2-wire miniJST conn pair, 1.5mm pitch. 100mm leads, 32 guage wire More info »
Carbon Fiber Graphite cloth sheet (8 X 20 inches) Weighs about 2.4oz per square yard. 1K tow. Plain weave (checkerboard pattern). Carbonfiber Cloth can be used to make lightweight Carbon Fiber Propellers by using a vacuum forming process. It can also be used to strengthen a project while adding minimal weight. Can be used with polyester or epoxy. Plain weave is a one over one under pattern, checkerboard-like. More info »
Carbon Fiber Graphite cloth sheet (8 X 20 inches) Weighs about 3.5oz per square yard. 1K tow. Plain weave (checkerboard pattern). Carbonfiber Cloth can be used to make lightweight Carbon Fiber Propellers by using a vacuum forming process. It can also be used to strengthen a project while adding minimal weight. Can be used with polyester or epoxy. More info »
A short length of 6K carbon fiber tow for Micro R/C builders. We use this material to stiffen and strengthen balsa parts - just lay on some fibers and hit it with CA glue or Epoxy - instant lightweight composite structure. We do this on the V-stab of the Carbon Butterfly and it comes in handy. Very fine fibers! More info »
Laser etched and cut to mount perfectly to the back of our 0.9g 3 channel receiver. Makes installation of the receiver a breeze. 6 pcs per card. More info »
Durobatics Foam Sheets - InkJet Ready (3 Sheets - 12" X 13", 0.020" - 0.025" thickness, White Color). These sheets are pre-doped and are ready to be printed by Inkjet printer with straight through paper feed. The ultimate light-weight building material for model aircraft. More info »
Durobatics Foam Sheets - Uncoated (3 Sheets - 12" X 13", 0.020" - 0.025" thickness, White Color). These sheets are uncoated and can not be printed on. The ultimate light-weight building material for model aircraft. More info »
Customer Service
My Cart
My Account
My Cart
View Cart
